Схема узла
Запчасти для посудомоечной машины Bauknecht GSF 2988 SG
Характеристики:
Fan for drying: Voltage 220/240 V (min.) | 220 V |
Water pressure: Inlet pressure | 0.3 bar - 10 bar |
Electronic boards: Serial boards (DB) | 4619 724 44721 |
Rotations: Drain pump motor | 3000 RPM |
Detergent capacity: Rinse aid dosage | 135 cm 3 |
Electronic boards: Serial boards (Data set) | 710995 |
Electronic boards: Serial boards (UCB programmed) | 4619 724 84451 |
Regeneration: Position 3 (after wash cycles) | 5 |
Spray pump motor: Voltage | 220/240 V |
Heating element: Temperature on surface | ~ 115 °C |
Potentiometer: Points of meassurement: (Position 2) | 1.0 k Ω |
Regeneration: Position 2 (Water hardness) | 11 - 15 °dh 1.9 - 2.7 mmol/l 19 - 27 °Fh |
Spray pump motor: HA | 60 Ω |
Detergent capacity: Prewash | 10 cm 3 |
Drain pump motor: Power Consumption | 30 W |
Coil of dispenser: Resistance | 1.3 k Ω |
Measuring the level: | Para medir el nivel de agua en la cuba, sacar el filtro y con un metro medir desde fondo del colector. |
Program information: | All programs will be locked after start. Changing the program or ?nishing the program will be possible only after pressing the start button for longer then 1.5 sec. (Break by customer) A switching off the appliance or unplug the appliance for a while, this will frozen the program step and later on, the program continuos on the same position. Exception: Switching off the appliance or unplug the appliance during the drying phase, this will lead directly to the end of the program. |
Spray arms, turning rhythm at alternating spray system: Intermediate rinse | Spray arm lower ~2min Upper arm ~2min Spray arm upper ~ 2 min |
Flow rates/ Inlet volume: Fan for drying (Total) | 900 l/min |
Электрические базовые данные: напряжение | 220/ 230 V |
Spray pump motor alternating spray system: Capacitor | 4 µ F |
Heating element: Safety thermostat self reset (Temperature of water) | ~ 85 °C |
Rotations: Spray pump motor | 2800 RPM |
Motor Diverter Valve: Signal (2x within ~13 sec.) | 5.0 V |
Heating element: | 1 Element system |
Electronic boards: Serial boards (Basic UCB, not programmed) | 4619 727 10995 see on the boards itself |
Single electric water inlet valve: Resistance | 3,76 k Ω |
Data Energy Label: Drying Performance | A |
Single electric water inlet valve: Voltage | 220/240 V |
Heating element: Power Consumption | 1.87/ 2.04 kW |
Regeneration valve: Frequency | 50/ 60 Hz |
Regeneration: Position 5 (Water hardness) | 29 - 35 °dh 5.1 - 6.3 mmol/l 51 - 63 °Fh |
Rotations: Spray arm upper | 30 RPM - 40 RPM |
Regeneration: Position 1 (after wash cycles) | 10 |
Regeneration: Position 0 (Water hardness) | 0 - 5 °dh 0 - 0.9 mmol/l 0 - 9 °Fh |
Succession of programs: Programs | A1a-A2a-A3a-A5a-A8a-A9a see program diagram |
Flow rates/ Inlet volume: Fan for drying (Primary air flow) | 210 l/min |
Water softener: Resin container | 900 cm 3 |
Motor Diverter Valve: Voltage | 220 V - 240 V |
Electronic boards: Serial boards (UB) | 4619 724 30921 DB 4619 724 44721 |
Potentiometer: Points of meassurement: (Position 3) | 1.4 k Ω |
Heating element: Voltage | 220/ 230 V |
Accessory: | If you need spare parts apart from the spare part list have a look in the Service Bulletin 4812 718 40084. |
Fan for drying: Voltage 220/240 V (max.) | 240 V |
Water softener: Salt container | 2 kg |
Regeneration: Position 2 (after wash cycles) | 7 |
Spray pump motor: HI | 79 Ω |
Alarms: Refill salt | Wasserhahn geschlossen |
Spray pump motor: Capacitor | 4 µ F |
Potentiometer: Points of meassurement: (Position 0) | 0.0 k Ω |
Options: | Zone washing Delay function |
Succession of programs: | Présten atención al diagrama programador |
Electronic boards: Serial boards (CB programmed) | 711005 |
Regeneration: Position 3 (Water hardness) | 16 - 21 °dh 2.8 - 3.7 mmol/l 28.37 °Fh |
Flow rates/ Inlet volume: Flow meter () | 208 |
Drain pump motor: Voltage | 220/ 240 V |
Spray arms, turning rhythm at alternating spray system: Final rinse | Spray arm lower ~2min Upper arm ~2min Spray arm upper ~ 2 min |
Regeneration: Position 0 (after wash cycles) | 12 |
Detergent capacity: Dosage steps | 1 ml - 6 ml |
Electrical base data: Total power | 2.0 kW - 2.2 kW |
Regeneration: Position 4 (Water hardness) | 22 - 28 °dh 3.8 - 5.0 mmol/l 38 - 50 °Fh |
Potentiometer: Points of meassurement: (Position 4) | 1.8 k Ω |
Regeneration: Volume () | 300 |
Coil of dispenser: Frequency | 50/ 60 Hz |
Spray pump motor alternating spray system: Power Consumption | 125 W |
Regeneration: Position 4 (after wash cycles) | 3 |
Dimensions + Weight: Product dimensions (Weight) | 58 kg |
Optical water indicator (OWI): Combination part of | Turbidity sensor (DON) Thermostat temp. sensor (notice NTC) |
Heating element: Fuse | 206 °C |
Motor Diverter Valve: Frequency | 50/ 60 Hz |
Regeneration valve: Resistance | 3.13 k Ω |
Electronic boards: Serial boards () | Programing of version and programmed control board, see "Service" and "Data set" on rating plate of inner door: |
Data Energy Label: Energy Performance | A |
Data Energy Label: Reference program | A5a |
Размеры + Вес: Размеры продукта (ширина) | 59,7 cm |
Drain pump motor: Resistance | 146 Ω |
Potentiometer: Points of meassurement: (Position 5) | 2.3 k Ω |
Spray pump motor alternating spray system: HI | 79 Ω |
Regeneration: Position 1 (Water hardness) | 6 - 10 °dh 1 - 1.8 mmol/l 10 - 18 °Fh |
Электрические базовые данные: частота | 50 Hz |
Электрические базовые данные: Потребляемая мощность | 2,0 kW - 2,2 kW |
Spray arms, turning rhythm at alternating spray system: Prewash | Spray arm lower ~3min Upper arm ~1min Spray arm upper ~ 1 min |
Coil of dispenser: Voltage | 220/ 240 V |
NTC | 20 °C 58.1 kΩ 25 °C 47.1 kΩ 30 °C 38.2 kΩ 40 °C 25.4 kΩ 50 °C 17.2 kΩ 60 °C 11.8 kΩ 70 °C 8.3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ 20 °C 58,1 kΩ 25 °C 47,1 kΩ 30 °C 38,2 kΩ 40 °C 25,4 kΩ 50 °C 17,2 kΩ 60 °C 11,8 kΩ 70 °C 8,3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ 20 °C 58,1 kΩ 25 °C 47,1 kΩ 30 °C 38,2 kΩ 40 °C 25,4 kΩ 50 °C 17,2 kΩ 60 °C 11,8 kΩ 70 °C 8,3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ |
Potentiometer: Points of meassurement: (Position 6) | 2.6 k Ω |
Электрическая база данных: Предохранитель | 10 A |
Spray pump motor alternating spray system: Voltage | 220/ 240 V |
Water pressure: Spray pump pressure | 0.3 bar 0,3 |
Размеры + Вес: Размеры продукта (Глубина) | 59,6 cm |
Spray arms, turning rhythm at alternating spray system: | Bemerkung: Nach Programmunterbrechungen im Testprogramm rotieren die Sprüharme wieder im Rhytmus des Hauptspülens (5/3 min). Wichtig: Zum Beenden des Testprogramms Startknopf länger als 1,5 s drücken. Nach Beendigung des Testprogramms (LED Ende an und/oder LED Start aus) muß das Gerät ausgeschaltet werden, andernfalls rotieren die Sprüharme beim nächsten Spülen weiter im Rhytmus des Testprogramms (30/30 s). |
Spray arms, turning rhythm at alternating spray system: Service Test program | Remark: When switching of the main switch or interrupt the mains during the Test Program runs, then the alternating of the spray arms change in the test program to the rhythm of main wash 5/3 min. Important: To leaf the Test program is possible by made a break by customer (pushing the start button for 1.5 sec.) After finishing the test program (End LED shines and/or Start LED goes of) must the appliance be switched off. If this will not be done, then the next normal wash will be made with the frequency of the Service Test Program ~30/30 sec. Spray arm lower ~30sec Upper arm ~30sec Spray arm upper ~ 30 s |
Regeneration valve: Voltage | 220/ 240 V |
Potentiometer: Points of meassurement: (Position 1) | 0.5 k Ω |
Rotations: Fan for drying | 2500 RPM |
Succession of programs: Succession | A1a - A2a - A3a - A5a - A8a - A9a |
Detergent capacity: Main wash | 40 cm 3 |
Spray arms, turning rhythm at alternating spray system: Main wash | Spray arm lower ~3min Upper arm ~5min Spray arm upper ~ 5 min |
Flow rates/ Inlet volume: Pump height max. () | 1,1 |
Water softener: Regeneration dosage | 300 cm 3 |
Heating element: Resistance | 24.5 Ω |
Water Volume: Water Volume Level | Regeneration 0.3 l 15 mm Back rinse 3x 1.0 l 60 mm Prewash 3.9 l 120 mm Main wash 3.2 l 118 mm Intermediate rinse 1 3.2 l 118 mm Intermediate rinse 2 3.2 l 118 mm Clear rinse 3.2 l 118 mm Safety/ overflow 8.5 l 141 mm Regenerieren 0,3 l 15 mm Rückspülen 3x 1,0 l 60 mm Vorspülen 3,9 l 116 mm Hauptspülen 3,2 l 112 mm Zwischenspülen 1 3,2 l 112 mm Zwischenspülen 2 3,2 l 112 mm Klarspülen 3,2 l 112 mm Sicherheitsniveau 8,5 l 141 mm Regeneración 0,3 l 15 mm Llenados limpieza 3x 1,0 l 60 mm Prelavado 3,9 l 120 mm Lavado 3,2 l 118 mm Aclarado intermedio 1 3,2 l 118 mm Aclarado intermedio 2 3,2 l 118 mm Aclarado final 3,2 l 118 mm Sobrenivel / seguridad 8,5 l 141 mm |
Regeneration: Position 6 (Water hardness) | 36 - 60 °dh 6.4 - 10.7 mmol/l 64 - 107 °Fh |
Regeneration: Position 6 (after wash cycles) | 1 |
Single electric water inlet valve: Frequency | 50/60 Hz |
Spray pump motor: Power Consumption | 125 W |
Heating element: Heating speed | ~ 2.0 °C/min |
Flow rates/ Inlet volume: Fan for drying (Secondary air flow) | 780 l/min |
Rotations: Spray arm lower | 30 RPM - 40 RPM |
Spray pump motor alternating spray system: HA | 60 Ω |
Regeneration: Position 5 (after wash cycles) | 2 |
Data Energy Label: Cleaning Performance | A |
Potentiometer: Points of meassurement: () | 1(black) to 2 (middle) |
Размеры + Вес: Размеры продукта (Высота) | 85,0 cm |
Motor Diverter Valve: Resistance | 6.5 k Ω |