Water hardness: Water hardness German degrees °dh French degrees °fh English degrees Clarke °e mmol/l Water softener setting is shown by flashing LED (1x-7x) or digital display (1-7)
1 soft 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x
1 - 2 soft/ medium 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x
2 medium 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x
3 medium/ hard 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x (DEFAULT SETTING)
4 hard 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x
4 very hard 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x
4 extremely hard 36 - 60 (53) 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x
Heating element: Type
1 Element system
Spray pump motor: Voltage
220/ 240 V
Heating element: Temperature on surface
~ 115 °C
Alarms: Refill rinse aid (rinse aid control)
Reed contact
Water softener setting
To change the water softener setting:Push the POWER button on Change to program 2 Hold the START button for 5 seconds until the LED is flashing is shown by flashing LED By pushing the START button you can change the setting Push the POWER button off to save and exit the water softener setting
Spray pump motor: HA
74.8 Ω
Detergent capacity: Prewash
10 cm³
Drain pump motor: Power Consumption
30 W
Coil of dispenser: Resistance
1.3 k Ω
Program information:
All programs will be locked after start. Changing the program or finishing the program will be possible only after pressing the start button for longer then 1.5 sec. (Break by customer)
A switching off the appliance or unplug the appliance for a while, this will frozen the program step and later on, the program continuos on the same position.
Exception: Switching off the appliance or unplug the appliance during the drying phase, this will lead directly to the end of the program.
Dimensions + Weight: Decor plate (Thickness)
max. 4 mm
Электрические базовые данные: напряжение
220/ 230 V
Spray pump motor: Frequency
50 Hz
Heating element: Safety thermostat self reset (Temperature of water)
85 °C
Flow meter: Flow rate
208 lmp/l
Programs: Succession of programs
see program diagram P1a - P3a - P5j - P6a - P7a/b
Drain pump motor: Flow rate
16 l/min
Electronic boards: Serial boards (Basic UCB, not programmed)
see on the boards itself 4619 727 50951
Single electric water inlet valve: Resistance
3.76 k Ω
Data Energy Label: Drying Performance
A
Single electric water inlet valve: Voltage
220/ 240 V
Heating element: Power Consumption
1.87/ 2.04 kW
Regeneration valve: Frequency
50/ 60 Hz
Alarms: Refill salt (salt control)
Reed contact
Water softener: Resin container
700 cm³
Heating element: Voltage
220/ 230 V
Accessory:
If you need spare parts apart from the spare part list have a look in the Service Bulletin 4812 718 40084.
For higher mounted Dishwashers to prevent the drain off effect - also usable for lower drain pipes and to
prevent the failure F8 use Kit 4812 310 18993.
Dimensions + Weight: Decor plate (Weight)
max. 1.8 kg
Water softener: Salt container
2 kg
Spray pump motor: HI
62 Ω
Spray pump motor: Capacitor
4 µF
Spray pump motor: Flow rate
67 l/min
Pump height max. 1.1 m
Spray arm lower ~ 33 l/min
Spray arm upper ~ 27 l/min
Shower/Spray arm top ~ 8 l/min
Regeneration: Volume
300 cm³
Drain pump motor: Voltage
220/ 240 V
Spray pump motor: Spray pump pressure
0.3 bar
Flow meter: Switch
Reed contact
Detergent capacity: Dosage steps
1 - 6 ml
Electrical base data: Total power
2.2 kW
Coil of dispenser: Frequency
50/ 60 Hz
Regeneration: after wash cycles
Depending on the water hardness
Dimensions + Weight: Product dimensions (Weight)
56 kg
Programs:
Permanent washing system
Single electric water inlet valve: Inlet pressure
0.3 bar - 10 bar
Volume: Water Volume Level
Regeneration 0.3 l 15 mm
Back rinse 3x 1.0 l 60 mm
Prewash 4.8 l 120 mm
Main wash 4.2 l 118 mm
Intermediate rinse 1 4.2 l 118 mm
Intermediate rinse 2 4.2 l 118 mm
Clear rinse 4.2 l 118 mm
Safety/ overflow 8.5 l 141 mm
Heating element: Fuse
206 °C
Regeneration valve: Resistance
3.13 k Ω
Electronic boards: Serial boards ()
Programmed control board and programing of version , see ,,Board Service" and ,,DATA" on rating plate of inner door:
Data Energy Label: Energy Performance
A
Drain pump motor: Rotations
3000 RPM
Data Energy Label: Reference program
P5j
Model
BU IC MID 5 INCORED
Размеры + Вес: Размеры продукта (ширина)
59.7 cm
Drain pump motor: Resistance
146 Ω
Электрические базовые данные: частота
50 Hz
Coil of dispenser: Voltage
220/ 240 V
NTC
20 °C 58,1 kΩ
25 °C 47,1 kΩ
30 °C 38,2 kΩ
40 °C 25,4 kΩ
50 °C 17,2 kΩ
60 °C 11,8 kΩ
70 °C 8,3 kΩ
80 °C 6 kΩ
85 °C 4 kΩ
Regeneration: Salt consumption for regeneration
~ 77 g
Электрическая база данных: Предохранитель
10 A
Размеры + Вес: Размеры продукта (Глубина)
59.6 cm
Regeneration valve: Voltage
220/ 240 V
Detergent capacity: Main wash
40 cm³
Water softener: Regeneration dosage
300 cm³
Heating element: Resistance
24,5 Ω
Single electric water inlet valve: Frequency
50/ 60 Hz
Spray pump motor: Power Consumption
130 W
Heating element: Heating speed
~ 2,0 °C/min
Electronic boards: Serial boards (For programing please use Service Assistance Module (S.A.M.))
4812 289 98001
plus cable 4812 289 98004
Dimensions + Weight: Decor plate (Width)
583 mm
Spray pump motor: Rotations
2800 RPM
Spray arm lower 30 RPM - 40 RPM
Spray arm upper 30 RPM - 40 RPM