Схема узла
Запчасти для посудомоечной машины Bauknecht GSFH 1888 WS
Характеристики:
Water pressure: Inlet pressure | 0.3 bar - 10 bar |
Rotations: Drain pump motor | 3000 RPM |
Detergent capacity: Rinse aid dosage | 135 cm 3 |
Electronic boards: Serial boards (Data set) | 719821 |
Flow rates/ Inlet volume: Shower/Spray arm top | ~ 8 l/min |
Spray pump motor: Voltage | 220/ 240 V |
Heating element: Temperature on surface | ~ 115 °C |
Flow rates/ Inlet volume: Fan for drying | Total 900 l/min Primary air flow 210 l/min Secondary air flow 780 l/min |
Motor Diverter Valve: Voltage 220/ 240 V (max.) | 240 V |
Water softener setting | Härtebereich einstellen (nach folgender Tabelle): Gerät einschalten Programm 2 wählen Start-Taste drücken (mindestens 5 Sekunden) bis Start LED blinkt Start LED blinkt bzw. Digitalanzeige leuchtet entsprechend der eingestellten Härte (siehe Tabelle) Start-Taste kurz drücken ändert die Einstellung um 1 und beginnt nach 7 wieder bei 1 Gerät ausschalten (Einstellung gespeichert) To change the water softener setting:· Push the POWER button on · Change to program 2 · Hold the START button for 5 seconds until the LED is flashing · is shown by flashing LED or digital display · By pushing the START button you can change the setting · Push the POWER button off to save and exit the water softener setting |
Spray pump motor: HA | 60 Ω |
Detergent capacity: Prewash | 10 cm 3 |
Drain pump motor: Power Consumption | 30 W |
Coil of dispenser: Resistance | 1.3 k Ω |
Flow rates/ Inlet volume: Spray pump | 45 l/min - 65 l/min |
Program information: | All programs will be locked after start. Changing the program or ?nishing the program will be possible only after pressing the start button for longer then 1.5 sec. (Break by customer) A switching off the appliance or unplug the appliance for a while, this will frozen the program step and later on, the program continuos on the same position. Exception: Switching off the appliance or unplug the appliance during the drying phase, this will lead directly to the end of the program. |
Spray arms, turning rhythm at alternating spray system: Intermediate rinse | Spray arm lower ~2min Upper arm ~2min Spray arm upper ~ 2 min |
Электрические базовые данные: напряжение | 220/ 240 V |
Spray pump motor alternating spray system: Capacitor | 4 µ F |
Heating element: Safety thermostat self reset (Temperature of water) | 85 °C |
Rotations: Spray pump motor | 2800 RPM |
Heating element: | 1 Element system |
Electronic boards: Serial boards (Basic UCB, not programmed) | 4619 727 01111 |
Single electric water inlet valve: Resistance | 3.76 k Ω |
Data Energy Label: Drying Performance | A |
Single electric water inlet valve: Voltage | 220/ 240 V |
Fan for drying: Voltage 220/ 240 V (max.) | 240 V |
Heating element: Power Consumption | 1.87/ 2.04 kW |
Regeneration valve: Frequency | 50/ 60 Hz |
Rotations: Spray arm upper | 30 RPM - 40 RPM |
Flow rates/ Inlet volume: Pump height max. | 1.1 m |
Flow rates/ Inlet volume: Spray arm lower | ~ 33 l/min |
Water softener: Resin container | 700 cm 3 |
Electronic boards: Serial boards (UB) | 4619 724 31351 DB 4619 724 30931 |
Heating element: Voltage | 220/ 240 V |
Flow rates/ Inlet volume: Inlet valve | 4 l/min |
Accessory: | If you need spare parts apart from the spare part list have a look in the Service Bulletin 4812 718 40084. |
Water softener: Salt container | 2 kg |
Spray pump motor: HI | 79 Ω |
Alarms: Refill salt | Wasserhahn geschlossen |
Spray pump motor: Capacitor | 4 µ F |
Options: | Zone washing Delay function Sani rinse program |
Electronic boards: Serial boards (CB programmed) | 719831 |
Regeneration: Volume | 300 cm 3 |
Drain pump motor: Voltage | 220/ 240 V |
Spray arms, turning rhythm at alternating spray system: Final rinse | Spray arm lower ~2min Upper arm ~2min Spray arm upper ~ 2 min |
Detergent capacity: Dosage steps | 1 ml - 6 ml |
Electrical base data: Total power | 2.0 kW - 2.2 kW |
Coil of dispenser: Frequency | 50/ 60 Hz |
Spray pump motor alternating spray system: Power Consumption | 125 W |
Regeneration: after wash cycles | abhängig von der Wasserhärte Depending on the water hardness |
Dimensions + Weight: Product dimensions (Weight) | 58 kg |
Water hardness: Water hardness German degrees °dH French degrees °fH English degrees Clarke °e mmol/l Water softener setting is shown by flashing LED (1x-7x) | 1 soft 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x 1 - 2 soft/ medium 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x 2 medium 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x 3 medium/ hard 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x (DEFAULT SETTING) 4 hard 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x 4 very hard 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x 4 extremely hard 36 - 60 (53) 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x 1 weich 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x 1 - 2 mittel 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x 2 mittel 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x 3 mittelhart 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x (Werkseinstellung) 4 hart 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x 4 sehr hart 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x 4 äußerst hart 36 - 60 (53) 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x |
Optical water indicator (OWI): Combination part of | Turbidity sensor (DON) Thermostat temp. sensor (notice NTC) |
Flow rates/ Inlet volume: Spray arm upper | ~ 27 l/min |
Heating element: Fuse | 206 °C |
Regeneration valve: Resistance | 3.13 k Ω |
Electronic boards: Serial boards () | Programing of version and programmed control board, see "Service" and "Data set" on rating plate of inner door: |
Motor Diverter Valve: Signal (2x within ~13 sec.) () | V |
Data Energy Label: Energy Performance | A |
Flow rates/ Inlet volume: Flow meter | 208 lmp/l |
Data Energy Label: Reference program | A5a |
Motor Diverter Valve: Voltage 220/ 240 V (min.) | 220 V |
Размеры + Вес: Размеры продукта (ширина) | 59.7 cm |
Drain pump motor: Resistance | 146 Ω |
Succession of programs: Programs () | see program diagram |
Spray pump motor alternating spray system: HI | 79 Ω |
Электрические базовые данные: частота | 50 Hz |
Электрические базовые данные: Потребляемая мощность | 2,0 kW - 2,2 kW |
Spray arms, turning rhythm at alternating spray system: Prewash | Spray arm lower ~3min Upper arm ~1min Spray arm upper ~ 1 min |
Coil of dispenser: Voltage | 220/ 240 V |
NTC | 20 °C 58.1 kΩ 25 °C 47.1 kΩ 30 °C 38.2 kΩ 40 °C 25.4 kΩ 50 °C 17.2 kΩ 60 °C 11.8 kΩ 70 °C 8.3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ 20 °C 58,1 kΩ 25 °C 47,1 kΩ 30 °C 38,2 kΩ 40 °C 25,4 kΩ 50 °C 17,2 kΩ 60 °C 11,8 kΩ 70 °C 8,3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ |
Fan for drying: Voltage 220/ 240 V (min.) | 220 V |
Regeneration: Salt consumption for regeneration | ~ 77 g |
Электрическая база данных: Предохранитель | 10 A |
Spray pump motor alternating spray system: Voltage | 220/ 240 V |
Water pressure: Spray pump pressure | 0.3 bar |
Размеры + Вес: Размеры продукта (Глубина) | 59.6 cm |
Spray arms, turning rhythm at alternating spray system: | Bemerkung: Nach Programmunterbrechungen im Testprogramm rotieren die Sprüharme wieder im Rhytmus des Hauptspülens (5/3 min). Wichtig: Zum Beenden des Testprogramms Startknopf länger als 1,5 s drücken. Nach Beendigung des Testprogramms (LED Ende an und/oder LED Start aus) muß das Gerät ausgeschaltet werden, andernfalls rotieren die Sprüharme beim nächsten Spülen weiter im Rhytmus des Testprogramms (30/30 s). |
Spray arms, turning rhythm at alternating spray system: Service Test program | Remark: When switching of the main switch or interrupt the mains during the Test Program runs, then the alternating of the spray arms change in the test program to the rhythm of main wash 5/3 min. After finishing the test program (End LED shines and/or Start LED goes of) must the appliance be switched off. Spray arm lower ~30sec Upper arm ~30sec Spray arm upper ~ 30 s |
Regeneration valve: Voltage | 220/ 240 V |
Rotations: Fan for drying | 2500 RPM |
Detergent capacity: Main wash | 40 cm 3 |
Spray arms, turning rhythm at alternating spray system: Main wash | Spray arm lower ~3min Upper arm ~5min Spray arm upper ~ 5 min |
Water softener: Regeneration dosage | 300 cm 3 |
Heating element: Resistance | 24.5 Ω |
Water Volume: Water Volume Level | Regeneration 0.3 l 15 mm Back rinse 3x 1.0 l 60 mm Prewash 3.9 l 120 mm Main wash 3.2 l 118 mm Intermediate rinse 1 3.2 l 118 mm Intermediate rinse 2 3.2 l 118 mm Clear rinse 3.2 l 118 mm Safety/ overflow 8.5 l 141 mm Regenerieren 0,3 l 15 mm Rückspülen 3x 1,0 l 60 mm Vorspülen 3,9 l 116 mm Hauptspülen 3,2 l 112 mm Zwischenspülen 1 3,2 l 112 mm Zwischenspülen 2 3,2 l 112 mm Klarspülen 3,2 l 112 mm Sicherheitsniveau 8,5 l 141 mm |
Single electric water inlet valve: Frequency | 50/ 60 Hz |
Water Volume: | Volumen bei Zonenwaschen gleich Volumen im Normalprogramm |
Spray pump motor: Power Consumption | 125 W |
Heating element: Heating speed | ~ 2.0 °C/min |
Rotations: Spray arm lower | 30 RPM - 40 RPM |
Spray pump motor alternating spray system: HA | 60 Ω |
Data Energy Label: Cleaning Performance | A |
Regeneration: Water hardness | 0 - 60 (53) °dh 0 - 10.7 mmol/l 0 - 107 °Fh |
Flow rates/ Inlet volume: Drain pump | 16 l/min |
Размеры + Вес: Размеры продукта (Высота) | 85.0 cm ± 1.4 |
Regeneration: Number of cycles with 2 kg salt | ~ 26 |