Схема узла
Запчасти для посудомоечной машины Bauknecht GSFS 4449
Выберите версию/индустриальный код: * От выбранной версии зависит совместимость запчастей
854844501810
Характеристики:
Water pressure: Inlet pressure 0.3 bar - 10 bar () | bar |
Rotations: Drain pump motor | 3000 RPM |
Detergent capacity: Rinse aid dosage | 135 cm 3 |
Electronic boards: Serial boards (Data set) | 470632 |
Regeneration with automatic salt adaption: after wash cycles | Depending on the water softener setting |
Flow rates/ Inlet volume: Shower/Spray arm top | ~ 8 l/min |
Electronic boards: Serial boards (UCB programmed) | 470642 User/Control Board |
Spray pump motor permant spray system: Voltage | 220/ 240 V |
Spray pump motor: Voltage | 220/240 V |
Heating element: Temperature on surface | ~ 115 °C |
Water softener setting | Härtebereich einstellen (nach folgender Tabelle): Gerät einschalten Programm 2 wählen Start-Taste drücken (mindestens 5 Sekunden) bis Anzeige Start blinkt Anzeige Start blinkt entsprechend der eingestellten Härte (siehe Tabelle) Start-Taste kurz drücken ändert die Einstellung um 1 und beginnt nach 7 wieder bei 1 Gerät ausschalten (Einstellung gespeichert) To change the water softener setting:· Push the POWER button on · Change to program 2 · Hold the START button for 5 seconds until the LED is flashing · is shown by flashing LED · By pushing the START button you can change the setting · Push the POWER button off to save and exit the water softener setting |
Detergent capacity: Prewash | 10 cm 3 |
Drain pump motor: Power Consumption | 30 W |
Flow rates/ Inlet volume: Spray pump | 45 l/min - 65 l/min 65 l/min 65 |
Program information: | All programs will be locked after start. Changing the program or ?nishing the program will be possible only after pressing the start button for longer then 1.5 sec. (Break by customer) A switching off the appliance or unplug the appliance for a while, this will frozen the program step and later on, the program continuos on the same position. Exception: Switching off the appliance or unplug the appliance during the drying phase, this will lead directly to the end of the program. |
Spray pump motor: Frequency | 50 Hz |
Coil of dispenser 30 Ω: Voltage | 220/ 240 V |
Heating element: Safety thermostat self reset (Temperature of water) | ~ 85 °C |
Rotations: Spray pump motor | 2800 RPM |
Heating element: | 1 Element system |
Electronic boards: Serial boards (Basic UCB, not programmed) | 4619 724 60952 see on board itself |
Electrical base data: Voltage 220/ 230 V (max.) | 230 V |
Single electric water inlet valve: Resistance | 3.76 k Ω |
Data Energy Label: Drying Performance | B |
Single electric water inlet valve: Voltage | 220/ 240 V |
Heating element: Power Consumption | 1.87/ 2.04 kW |
Regeneration valve: Frequency | 50/ 60 Hz |
Rotations: Spray arm upper | 30 RPM - 40 RPM |
Regeneration with automatic salt adaption: Volume | 300 cm 3 |
Flow rates/ Inlet volume: Pump height max. | 1.1 m |
Flow rates/ Inlet volume: Spray arm lower | ~ 33 l/min |
Water softener: Resin container | 900 cm 3 |
Heating element: Voltage | 220/ 230 V |
Flow rates/ Inlet volume: Inlet valve | 4 l/min |
Accessory: | If you need spare parts apart from the spare part list have a look in the Service Bulletin 4812 718 40084. |
Water softener: Salt container | 2 kg |
Spray pump motor permant spray system: Frequency | 50 Hz |
Electrical base data: Voltage 220/ 230 V (min.) | 220 V |
Dimensions + Weight: Product dimensions () | Free standing appliances with flat/ square outer door |
Regeneration: Volume | 300 cm 3 |
Drain pump motor: Voltage | 220/ 240 V |
Coil of dispenser 30 Ω: Resistance | 1.3 k Ω |
Spray pump motor: Resistance | 30 Ω |
Detergent capacity: Dosage steps | 1 à 6 cm 3 min. 1 ml max. 6 ml |
Regeneration: after wash cycles | 1 Depending on the water hardness |
Dimensions + Weight: Product dimensions (Weight) | 56 kg |
Flow rates/ Inlet volume: Spray arm upper | ~ 27 l/min Sprayarm/ Shower top ~ 8 l/min |
Volume: Water Volume Level | Regeneration 0.3 l 15 mm Back rinse 3x 1.0 l 60 mm Prewash 4.8 l 120 mm Main wash 4.2 l 118 mm Intermediate rinse 1 4.2 l 118 mm Intermediate rinse 2 4.2 l 118 mm Clear rinse 4.2 l 118 mm Safety/ overflow 8.5 l 141 mm Regenerieren 0,3 l 15 mm Rückspülen 3x 1,0 l 60 mm Vorspülen 4,8 l 120 mm Hauptspülen 4,2 l 118 mm Zwischenspülen 1 4,2 l 118 mm Zwischenspülen 2 4,2 l 118 mm Klarspülen 4,2 l 118 mm Sicherheitsniveau 8,5 l 141 mm REGENERATION 0,3 l 15 mm RINÇAGE 1,0 l 68 mm PRELAVAGE 4,8 l 124 mm LAVAGE 4,2 l 122 mm 1er RINÇAGE INTERMED 4,2 l 120 mm 2er RINÇAGE INTERMED 4,2 l 120 mm RINÇAGE FINAL 4,2 l 120 mm SECURITE/ANTI-DEBORD 8,5 l 141 mm |
Water hardness: water hardness Water hardness German degrees °dH French degrees °fH English degrees Clarke °e mmol/l Water softener setting is shown by flashing LED | 1 soft 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x 1 - 2 soft/ medium 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x 2 medium 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x 3 medium/ hard 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x 4 hard 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x 4 very hard 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x 4 extremely hard 36 - 60 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x 1 weich 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x 1 - 2 mittel 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x 2 mittel 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x 3 mittelhart 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x 4 hart 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x 4 sehr hart 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x 4 äußerst hart 36 - 40 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x 1 doux 0 - 9 0 - 0.9 1 x 1 - 2 doux/ moyen 10 - 18 1 - 1.8 2 x 2 moyen 19 - 27 1.9 - 2.7 3 x 3 moyen/ dur 28 - 37 2.8 - 3.7 4 x 4 dur 38 - 50 3.8 - 5.0 5 x 4 très dur 51 - 63 5.1 - 6.3 6 x 4 extrêmement dur 64 - 107 6.4 - 10.7 7 x |
Heating element: Fuse | 206 °C |
Regeneration valve: Resistance | 3.13 k Ω |
Electronic boards: Serial boards () | Programmed control board and programing of version , see ,,Board Service" and ,,DATA" on rating plate of inner door: |
Data Energy Label: Energy Performance | A |
Flow rates/ Inlet volume: Flow meter | 208 lmp/l |
Data Energy Label: Reference program | P5c |
Размеры + Вес: Размеры продукта (ширина) | 59.7 cm |
Drain pump motor: Resistance | 146 Ω |
Succession of programs: Programs () | see program diagram |
Water softener: Resin container quantity | 700 cm 3 |
NTC | 20 °C 58.1 kΩ 25 °C 47.1 kΩ 30 °C 38.2 kΩ 40 °C 25.4 kΩ 50 °C 17.2 kΩ 60 °C 11.8 kΩ 70 °C 8.3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ 20 °C 58,1 kΩ 25 °C 47,1 kΩ 30 °C 38,2 kΩ 40 °C 25,4 kΩ 50 °C 17,2 kΩ 60 °C 11,8 kΩ 70 °C 8,3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ 20 °C 58,1 kΩ 25 °C 47,1 kΩ 30 °C 38,2 kΩ 40 °C 25,4 kΩ 50 °C 17,2 kΩ 60 °C 11,8 kΩ 70 °C 8,3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ |
Regeneration: Salt consumption for regeneration | ~ 77 g |
Размеры + Вес: Размеры продукта (Глубина) | 59.6 cm |
Regeneration valve: Voltage | 220/ 240 V |
Detergent capacity: Main wash | 40 cm 3 |
Water softener: Regeneration dosage | 300 cm 3 |
Heating element: Resistance | 24.5 Ω |
Coil of dispenser 30 Ω: Frequency | 50/ 60 Hz |
Single electric water inlet valve: Frequency | 50/ 60 Hz |
Spray pump motor: Power Consumption | 80 W |
Spray pump motor permant spray system: Power Consumption | 80 W |
Heating element: Heating speed | ~ 2.0 °C/min ~ 2,0 |
Rotations: Spray arm lower | 30 RPM - 40 RPM |
Spray pump motor permant spray system: Resistance | 30 Ω |
Data Energy Label: Cleaning Performance | A |
Regeneration: Water hardness | 0 - 40 °dh 0 - 10,7 mmol/l 0 - 107 °Fh |
Flow rates/ Inlet volume: Drain pump | 16 l/min |
Размеры + Вес: Размеры продукта (Высота) | 85.0 cm |
Regeneration: Number of cycles with 2 kg salt | ~ 26 |