Схема узла
Запчасти для посудомоечной машины Bauknecht GSIE 6527/1 IN
Выберите версию/индустриальный код: * От выбранной версии зависит совместимость запчастей
854659822720
Характеристики:
Water pressure: Inlet pressure | 0,3 bar - 10 bar |
Electronic boards: Serial boards | Data set 758851 CB programmed 758861 UB 4619 727 49662 DB 4619 724 89912 Basic UCB, not programmed 4619 727 47651 |
Rotations: Drain pump motor | 3000 UPM |
Detergent capacity: Rinse aid dosage | 135 cm 3 |
Dimensions + Weight: Wooden door (Height) | 515 mm - 600 mm |
Flow rates/ Inlet volume: Shower/Spray arm top | ~ 8 l/min |
Spray pump motor: Voltage | 220/240 V |
Heating element: Temperature on surface | ~ 115 °C |
Spray pump motor: HA | 60 Ω |
Detergent capacity: Prewash | 10 cm 3 |
Drain pump motor: Power Consumption | 30 W |
Coil of dispenser: Resistance | 1,3 k Ω |
Flow rates/ Inlet volume: Spray pump | 45 l/min - 65 l/min |
Spray arms, turning rhythm at alternating spray system: Intermediate rinse | Spray arm lower ~ 2 min Spray arm upper ~ 2 min |
Электрические базовые данные: напряжение | 220/230 V |
Mix valve for Regeneration: Resistance | 2,0 k Ω |
Heating element: Safety thermostat self reset (Temperature of water) | 85 °C |
Mix valve for Regeneration: Voltage | 220/ 240 V |
Rotations: Spray pump motor | 2800 UPM |
Motor Diverter Valve: Signal (2x within ~13 sec.) | V |
Single electric water inlet valve: Resistance | 3,76 k Ω |
Data Energy Label: Drying Performance | A |
Single electric water inlet valve: Voltage | 220/240 V |
Heating element: Power Consumption | 1,87/2,04 kW |
Water Volume: Wasser Inhalt Höhe | Regenerieren 0,3 l 15 mm Rückspülen 3x 1,0 l 60 mm Vorspülen 3,9 l 116 mm Hauptspülen 3,2 l 112 mm Zwischenspülen 1 3,2 l 112 mm Zwischenspülen 2 3,2 l 112 mm Klarspülen 3,2 l 112 mm Sicherheitsniveau 8,5 l 141 mm |
Regeneration valve: Frequency | 50/60 Hz |
Rotations: Spray arm upper | 30 UPM - 40 UPM |
Flow rates/ Inlet volume: Pump height max. | 1,1 m |
Flow rates/ Inlet volume: Spray arm lower | ~ 33 l/min |
Water softener: Resin container | 900 cm 3 |
Motor Diverter Valve: Voltage | 220 V - 240 V |
Heating element: Voltage | 220/230 V |
Flow rates/ Inlet volume: Inlet valve | 4 l/min |
Mix valve for Regeneration: Frequency | 50/60 Hz |
Water softener: Salt container | 2 kg |
Spray pump motor: HI | 79 Ω |
Spray pump motor: Capacitor | 4 µ F |
Dimensions + Weight: Wooden door (Max. stick out over lower edge of appliance door) | 92 mm |
Regeneration: Volume | 300 cm 3 |
Drain pump motor: Voltage | 220/240 V |
Spray arms, turning rhythm at alternating spray system: Final rinse | Spray arm lower ~ 2 min Spray arm upper ~ 2 min |
Detergent capacity: Dosage steps | 1 ml - 6 ml |
Coil of dispenser: Frequency | 50/60 Hz |
Dimensions + Weight: Product dimensions (Weight) | 50 kg |
Flow rates/ Inlet volume: Spray arm upper | ~ 27 l/min |
Heating element: Fuse | 206 °C |
Motor Diverter Valve: Frequency | 50/60 Hz |
Regeneration valve: Resistance | 3,13 k Ω |
Data Energy Label: Energy Performance | A |
Flow rates/ Inlet volume: Flow meter | 208 lmp/l |
Data Energy Label: Reference program | A5h |
Размеры + Вес: Размеры продукта (ширина) | 59,7 cm |
Drain pump motor: Resistance | 146 Ω |
Электрические базовые данные: частота | 50 Hz |
Электрические базовые данные: Потребляемая мощность | 2,0 kW - 2,2 kW |
Spray arms, turning rhythm at alternating spray system: Prewash | Spray arm lower ~ 3 min Spray arm upper ~ 1 min |
Coil of dispenser: Voltage | 220/240 V |
NTC | 20 °C 58,1 kΩ 25 °C 47,1 kΩ 30 °C 38,2 kΩ 40 °C 25,4 kΩ 50 °C 17,2 kΩ 60 °C 11,8 kΩ 70 °C 8,3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ |
Regeneration: Salt consumption for regeneration | ~ 77 g |
Dimensions + Weight: Wooden door (Height of plinth) | min. 93 mm |
Water hardness: Härtestufe Deutscher Härtegrad °dH Franz. Härtegrad °fH Englischer Härte- grad Clarke °e mmol/l Einstellung Blinkfrequenz LED (1x-7x) bzw. Digitalanzeige (1-7) | 1 weich 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x 1 - 2 mittel 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x 2 mittel 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x 3 mittelhart 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x (Werkseinstellung) 4 hart 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x 4 sehr hart 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x 4 äußerst hart 36 - 60 (53) 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x |
Электрическая база данных: Предохранитель | 10 A |
Water pressure: Spray pump pressure | 0,3 bar |
Размеры + Вес: Размеры продукта (Глубина) | 55,5 cm |
Spray arms, turning rhythm at alternating spray system: | Bemerkung: Nach Programmunterbrechungen im Testprogramm rotieren die Sprüharme wieder im Rhytmus des Hauptspülens (5/3 min). Wichtig: Zum Beenden des Testprogramms Startknopf länger als 1,5 s drücken. Nach Beendigung des Testprogramms (LED Ende an und/oder LED Start aus) muß das Gerät ausgeschaltet werden, andernfalls rotieren die Sprüharme beim nächsten Spülen weiter im Rhytmus des Testprogramms (30/30 s). |
Dimensions + Weight: Wooden door (Width) | 592 mm - 595 mm |
Spray arms, turning rhythm at alternating spray system: Service Test program | Spray arm lower ~ 30 s Spray arm upper ~ 30 s |
Regeneration valve: Voltage | 220/240 V |
Succession of programs: Succession | A1a - A3a - A5h - A7e - A10a |
Dimensions + Weight: Wooden door (Weight) | max. 5,5 kg |
Detergent capacity: Main wash | 40 cm 3 |
Spray arms, turning rhythm at alternating spray system: Main wash | Spray arm lower ~ 3 min Spray arm upper ~ 5 min |
Water softener: Regeneration dosage | 300 cm 3 |
Heating element: Resistance | 24,5 Ω |
Single electric water inlet valve: Frequency | 50/60 Hz |
Dimensions + Weight: Wooden door (Thickness) | 16 mm - 20 mm |
Spray pump motor: Power Consumption | 125 W |
Heating element: Heating speed | ~ 2,0 °C/min |
Rotations: Spray arm lower | 30 UPM - 40 UPM |
Data Energy Label: Cleaning Performance | A |
Regeneration: Water hardness | 0 - 60 (53) °dh 0 - 10,7 mmol/l 0 - 107 °Fh |
Flow rates/ Inlet volume: Drain pump | 16 l/min |
Размеры + Вес: Размеры продукта (Высота) | 82,0 cm - 87,0 cm |
Motor Diverter Valve: Resistance | 6,5 k Ω |
Regeneration: Number of cycles with 2 kg salt | ~ 26 |