Схема узла
Запчасти для посудомоечной машины Bauknecht GSIP 6527 SW
Выберите версию/индустриальный код: * От выбранной версии зависит совместимость запчастей
854665201720
Характеристики:
Water pressure: Inlet pressure | 0.3 bar - 10 bar |
Rotations: Drain pump motor | 3000 RPM |
Detergent capacity: Rinse aid dosage | 135 cm 3 |
Dimensions + Weight: Wooden door (Height) | 515 mm - 600 mm |
Dimensions + Weight: Wooden door for Integrable types (Weight) | max. 5.5 kg |
Flow rates/ Inlet volume: Shower/Spray arm top | ~ 8 l/min |
Spray pump motor: Voltage | 220/ 240 V |
Heating element: Temperature on surface | ~ 115 °C |
Electronic boards: Serial boards DB 4619 724 89912 (UB) | 4619 724 8678 DB 4619 724 89912 |
Motor Diverter Valve: Voltage 220/ 240 V (max.) | 240 V |
Water softener setting | Härtebereich einstellen (nach folgender Tabelle): Gerät einschalten Programm 2 wählen Start-Taste drücken (mindestens 5 Sekunden) bis Start LED blinkt Start LED blinkt bzw. Digitalanzeige leuchtet entsprechend der eingestellten Härte (siehe Tabelle) Start-Taste kurz drücken ändert die Einstellung um 1 und beginnt nach 7 wieder bei 1 Gerät ausschalten (Einstellung gespeichert) To change the water softener setting:· Push the POWER button on · Change to program 2 · Hold the START button for 5 seconds until the LED is flashing · is shown by flashing LED or digital display · By pushing the START button you can change the setting · Push the POWER button off to save and exit the water softener setting |
Spray pump motor: HA | 70,2 Ω |
Detergent capacity: Prewash | 10 cm 3 |
Drain pump motor: Power Consumption | 30 W |
Coil of dispenser: Resistance | 1.3 k Ω |
Flow rates/ Inlet volume: Spray pump | 67 l/min min. 45 l/min max. 65 l/min |
Electronic boards: Service boards () | siehe Ersatzteilliste |
Program information: | All programs will be locked after start. Changing the program or ?nishing the program will be possible only after pressing the start button for longer then 1.5 sec. (Break by customer) A switching off the appliance or unplug the appliance for a while, this will frozen the program step and later on, the program continuos on the same position. Exception: Switching off the appliance or unplug the appliance during the drying phase, this will lead directly to the end of the program. |
Spray arms, turning rhythm at alternating spray system: Intermediate rinse | Spray arm lower ~2min Upper arm ~2min Spray arm upper ~ 2 min |
Электрические базовые данные: напряжение | 220/ 240 V |
Spray pump motor alternating spray system: Capacitor | 4 µ F |
Mix valve for Regeneration: Resistance | 2,0 k Ω |
Heating element: Safety thermostat self reset (Temperature of water) | 85 °C |
Mix valve for Regeneration: Voltage | 220/ 240 V |
Rotations: Spray pump motor | 2800 RPM |
Heating element: | 1 Element system |
Single electric water inlet valve: Resistance | 3.76 k Ω |
Data Energy Label: Drying Performance | A |
Single electric water inlet valve: Voltage | 220/ 240 V |
Heating element: Power Consumption | 1.87/ 2.04 kW |
Regeneration valve: Frequency | 50/ 60 Hz |
Rotations: Spray arm upper | 30 RPM - 40 RPM |
Flow rates/ Inlet volume: Pump height max. | 1.1 m |
Flow rates/ Inlet volume: Spray arm lower | ~ 33 l/min |
Dimensions + Weight: Wooden door for Integrable types (Width) | 592 mm - 595 mm |
Dimensions + Weight: Wooden door for Integrable types (Max. stick out over lower edge of appliance door) | 92 mm |
Water softener: Resin container | 700 cm 3 |
Heating element: Voltage | 220/ 240 V |
Flow rates/ Inlet volume: Inlet valve | 4 l/min |
Accessory: | If you need spare parts apart from the spare part list have a look in the Service Bulletin 4812 718 40084. For higher mounted Dishwashers to prevent the drain off effect - also usable for lower drain pipes and to prevent the failure F8 use Kit 4812 310 18993. |
Mix valve for Regeneration: Frequency | 50/60 Hz |
Water softener: Salt container | 2 kg |
Spray pump motor: HI | 59 Ω |
Spray pump motor: Capacitor | 4 µ F |
Dimensions + Weight: Wooden door (Max. stick out over lower edge of appliance door) | 92 mm |
Options: | Zone washing Delay function |
Dimensions + Weight: Wooden door for Integrable types (Height of plinth) | min. 93 mm |
Regeneration: Volume | 300 cm 3 |
Drain pump motor: Voltage | 220/ 240 V |
Spray arms, turning rhythm at alternating spray system: Final rinse | Spray arm lower ~2min Upper arm ~2min Spray arm upper ~ 2 min |
Detergent capacity: Dosage steps | 1 ml - 6 ml |
Electrical base data: Total power | 2.0 kW - 2.2 kW |
Coil of dispenser: Frequency | 50/ 60 Hz |
Spray pump motor alternating spray system: Power Consumption | 125 W |
Regeneration: after wash cycles | abhängig von der Wasserhärte Depending on the water hardness |
Dimensions + Weight: Product dimensions (Weight) | 50 kg |
Dimensions + Weight: Wooden door for Integrable types (Height) | 515 mm - 600 mm |
Water hardness: Water hardness German degrees °dH French degrees °fH English degrees Clarke °e mmol/l Water softener setting is shown by flashing LED (1x-7x) | 1 soft 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x 1 - 2 soft/ medium 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x 2 medium 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x 3 medium/ hard 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x (DEFAULT SETTING) 4 hard 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x 4 very hard 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x 4 extremely hard 36 - 60 (53) 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x 1 weich 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x 1 - 2 mittel 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x 2 mittel 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x 3 mittelhart 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x (Werkseinstellung) 4 hart 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x 4 sehr hart 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x 4 äußerst hart 36 - 60 (53) 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x |
Flow rates/ Inlet volume: Spray arm upper | ~ 27 l/min |
Heating element: Fuse | 206 °C |
Regeneration valve: Resistance | 3.13 k Ω |
Motor Diverter Valve: Signal (2x within ~13 sec.) () | V |
Electronic boards: Serial boards DB 4619 724 89912 (Basic UCB, not programmed) | 4619 727 47651 siehe Boardaufdruck |
Data Energy Label: Energy Performance | A |
Flow rates/ Inlet volume: Flow meter | 208 lmp/l |
Data Energy Label: Reference program | A5h |
Motor Diverter Valve: Voltage 220/ 240 V (min.) | 220 V |
Размеры + Вес: Размеры продукта (ширина) | 59.7 cm |
Drain pump motor: Resistance | 146 Ω |
Electronic boards: Serial boards DB 4619 724 89912 (Data set) | 745871 |
Succession of programs: Programs () | see program diagram |
Spray pump motor alternating spray system: HI | 79 Ω |
Dimensions + Weight: Wooden door for Integrable types (Thickness) | 16 mm - 20 mm |
Электрические базовые данные: частота | 50 Hz |
Электрические базовые данные: Потребляемая мощность | 2,2 kW |
Spray arms, turning rhythm at alternating spray system: Prewash | Spray arm lower ~3min Upper arm ~1min Spray arm upper ~ 1 min |
Coil of dispenser: Voltage | 220/ 240 V |
NTC | 20 °C 58.1 kΩ 25 °C 47.1 kΩ 30 °C 38.2 kΩ 40 °C 25.4 kΩ 50 °C 17.2 kΩ 60 °C 11.8 kΩ 70 °C 8.3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ 20 °C 58,1 kΩ 25 °C 47,1 kΩ 30 °C 38,2 kΩ 40 °C 25,4 kΩ 50 °C 17,2 kΩ 60 °C 11,8 kΩ 70 °C 8,3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ |
Regeneration: Salt consumption for regeneration | ~ 77 g |
Dimensions + Weight: Wooden door (Height of plinth) | min. 93 mm |
Электрическая база данных: Предохранитель | 10 A |
Spray pump motor alternating spray system: Voltage | 220/ 240 V |
Water pressure: Spray pump pressure | 0.3 bar |
Размеры + Вес: Размеры продукта (Глубина) | 57.0 cm |
Spray arms, turning rhythm at alternating spray system: | Bemerkung: Nach Programmunterbrechungen im Testprogramm rotieren die Sprüharme wieder im Rhytmus des Hauptspülens (5/3 min). Wichtig: Zum Beenden des Testprogramms Startknopf länger als 1,5 s drücken. Nach Beendigung des Testprogramms (LED Ende an und/oder LED Start aus) muß das Gerät ausgeschaltet werden, andernfalls rotieren die Sprüharme beim nächsten Spülen weiter im Rhytmus des Testprogramms (30/30 s). |
Dimensions + Weight: Wooden door (Width) | 592 mm - 595 mm |
Spray arms, turning rhythm at alternating spray system: Service Test program | Remark: When switching of the main switch or interrupt the mains during the Test Program runs, then the alternating of the spray arms change in the test program to the rhythm of main wash 5/3 min. After finishing the test program (End LED shines and/or Start LED goes of) must the appliance be switched off. If this will not be done, then the next normal wash will be made with the frequency of the Service Test Program ~30/30sec. Spray arm lower ~30sec Upper arm ~30sec Spray arm upper ~ 30 s |
Regeneration valve: Voltage | 220/ 240 V |
Dimensions + Weight: Wooden door (Weight) | max. 5,5 kg |
Detergent capacity: Main wash | 40 cm 3 |
Spray arms, turning rhythm at alternating spray system: Main wash | Spray arm lower ~3min Upper arm ~5min Spray arm upper ~ 5 min |
Water softener: Regeneration dosage | 300 cm 3 |
Heating element: Resistance | 24.5 Ω |
Water Volume: Water Volume Level | Regeneration 0.3 l 15 mm Back rinse 3x 1.0 l 60 mm Prewash 3.9 l 120 mm Main wash 3.2 l 118 mm Intermediate rinse 1 3.2 l 118 mm Intermediate rinse 2 3.2 l 118 mm Clear rinse 3.2 l 118 mm Safety/ overflow 8.5 l 141 mm Regenerieren 0,3 l 15 mm Rückspülen 3x 1,0 l 60 mm Vorspülen 3,9 l 116 mm Hauptspülen 3,2 l 112 mm Zwischenspülen 1 3,2 l 112 mm Zwischenspülen 2 3,2 l 112 mm Klarspülen 3,2 l 112 mm Sicherheitsniveau 8,5 l 141 mm |
Single electric water inlet valve: Frequency | 50/ 60 Hz |
Dimensions + Weight: Wooden door (Thickness) | 16 mm - 20 mm |
Spray pump motor: Power Consumption | 120 W |
Heating element: Heating speed | ~ 2.0 °C/min |
Rotations: Spray arm lower | 30 RPM - 40 RPM |
Electronic boards: Serial boards DB 4619 724 89912 () | Programing of version and programmed control board, see "Service" and "Data set" on rating plate of inner door: |
Spray pump motor alternating spray system: HA | 60 Ω |
Data Energy Label: Cleaning Performance | A |
Regeneration: Water hardness | 0 - 60 (53) °dh 0 - 10.7 mmol/l 0 - 107 °Fh |
Electronic boards: Serial boards DB 4619 724 89912 (CB programmed) | 745881 |
Flow rates/ Inlet volume: Drain pump | 16 l/min |
Размеры + Вес: Размеры продукта (Высота) | 82.0 - 87.0cm |
Regeneration: Number of cycles with 2 kg salt | ~ 26 |