Схема узла
Запчасти для посудомоечной машины Whirlpool ADG 7557/2
Выберите версию/индустриальный код: * От выбранной версии зависит совместимость запчастей
851175501890
Характеристики:
Motor pump heater: Fuse | 206 °C |
Water pressure: Inlet pressure | 0,3 bar - 10 bar |
Motor pump heater: Single Phase Synchronous motor | Winding resistance (T=20°C) 29,2 Ω Resistance Heater (T=20°C) 28,2 Ω Temperature on surface ~ 115 °C |
Rotations: Drain pump motor | 3000 UPM |
Detergent capacity: Rinse aid dosage | 135 cm 3 |
Dimensions + Weight: Wooden door (Height) | 620 mm - 718 mm |
Electronic boards: Serial boards (Data set) | 549911 |
Flow rates/ Inlet volume: Shower/Spray arm top | ~ 8 l/min |
Electronic boards: Serial boards (UCB programmed) | 549921 |
Heating element: Temperature on surface | ~ 115 °C |
Detergent capacity: Prewash | 10 cm 3 |
Drain pump motor: Power Consumption | 30 W |
Coil of dispenser: Resistance | 1,3 k Ω |
Flow rates/ Inlet volume: Spray pump | 65 l/min ± 5 |
Electronic boards: Service boards () | siehe Ersatzteilliste |
Program information: | End - Acoustic signal Alle Programme werden nach dem Programmstart verriegelt. Zum Ändern oder Beenden des gewählten Programms Startknopf länger als 1,5 s drücken. Bei Programmunterbrechungen läuft das Programm von der Stopposition an weiter. Ausnahme: Bei Programmunterbrechung in der Trocknungsphase wird das Programm beendet. |
Volume: Wasser Inhalt Höhe | Regenerieren 0,3 l 15 mm Rückspülen 3x 1,0 l 60 mm Vorspülen 4,8 l 120 mm Hauptspülen 4,2 l 118 mm Zwischenspülen 1 4,2 l 118 mm Zwischenspülen 2 4,2 l 118 mm Klarspülen 4,2 l 118 mm Sicherheitsniveau 8,5 l 141 mm |
Электрические базовые данные: напряжение | 220/ 240 V |
Heating element: Safety thermostat self reset (Temperature of water) | 85 °C |
Rotations: Spray pump motor | 2800 UPM |
Heating element: | 1 Element system |
Electronic boards: Serial boards (Basic UCB, not programmed) | 4619 727 50961 siehe Boardaufdruck |
Single electric water inlet valve: Resistance | 3,76 k Ω |
Data Energy Label: Drying Performance | A |
Single electric water inlet valve: Voltage | 220/ 240 V |
Heating element: Power Consumption | 1,87/2,04 kW |
Regeneration valve: Frequency | 50/60 Hz |
Motor pump heater: Power Consumption | 2040 W ± 5 % |
Rotations: Spray arm upper | 30 UPM - 40 UPM |
Water hardness: Härtestufe Deutscher Härtegrad °dh Franz. Härtegrad °fh Englischer Härte- grad Clarke °e mmol/l Einstellung Blinkfrequenz LED (1x-7x) bzw. Digitalanzeige (1-7) | 1 weich 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x 1 - 2 mittel 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x 2 mittel 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x 3 mittelhart 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x (Werkseinstellung) 4 hart 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x 4 sehr hart 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x 4 äußerst hart 36 - 60 (53) 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x |
Flow rates/ Inlet volume: Pump height max. | 1,1 m |
Flow rates/ Inlet volume: Spray arm lower | ~ 33 l/min |
Water softener: Resin container | 700 cm 3 |
Heating element: Voltage | 220/ 240 V |
Flow rates/ Inlet volume: Inlet valve | 4 l/min |
Accessory: | Werden Teile benötigt, die nicht in der Ersatzteilliste aufgeführt sind, siehe Service Bulletin 4812 728 40084. Für Hocheinbau von Geschirrspülern um den Saugeffekt zu vermeiden - einsetzbar auch bei tie?iegenden Ab?üssen und zur Vermeidung der Fehlermeldung F8 - Kit 4812 310 18993. |
Water softener: Salt container | 2 kg |
Dimensions + Weight: Wooden door (Max. stick out over lower edge of appliance door) | 92 mm |
Options: | Zone washing |
Regeneration: Volume | 300 cm 3 |
Drain pump motor: Voltage | 220/ 240 V |
Detergent capacity: Dosage steps | 1 - 6 ml |
Coil of dispenser: Frequency | 50/60 Hz |
Water safety option: Waterstop system | Mechanical waterstop |
Regeneration: after wash cycles | Depending on the water hardness |
Dimensions + Weight: Product dimensions (Weight) | 50 kg |
Flow rates/ Inlet volume: Spray arm upper | ~ 27 l/min |
Heating element: Fuse | 206 °C |
Regeneration valve: Resistance | 3,13 k Ω |
Electronic boards: Serial boards () | siehe Boardaufdruck |
Data Energy Label: Energy Performance | A |
Flow rates/ Inlet volume: Flow meter | 208 lmp/l |
Data Energy Label: Reference program | P5j |
Размеры + Вес: Размеры продукта (ширина) | 59,7 cm |
Drain pump motor: Resistance | 146 Ω |
Succession of programs: Programs () | siehe Schließschema |
Motor pump heater: Safety thermostat self reset (Temperature of water) | 85 °C |
Электрические базовые данные: частота | 50 Hz |
Электрические базовые данные: Потребляемая мощность | 2,0 kW - 2,2 kW |
Coil of dispenser: Voltage | 220/ 240 V |
NTC | 20 °C 58,1 kΩ 25 °C 47,1 kΩ 30 °C 38,2 kΩ 40 °C 25,4 kΩ 50 °C 17,2 kΩ 60 °C 11,8 kΩ 70 °C 8,3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ |
Regeneration: Salt consumption for regeneration | ~ 77 g |
Dimensions + Weight: Wooden door (Height of plinth) | min. 93 mm |
Water softener setting Ω Ω Ω Ω Ω Ω: | (nach folgender Tabelle) |
Электрическая база данных: Предохранитель | 10 A |
Water pressure: Spray pump pressure | 315 mbar |
Размеры + Вес: Размеры продукта (Глубина) | 57,0 cm |
Dimensions + Weight: Wooden door (Width) | 592 mm - 595 mm |
Regeneration valve: Voltage | 220/ 240 V |
Dimensions + Weight: Wooden door (Weight) | max. 6,5 kg |
Detergent capacity: Main wash | 40 cm 3 |
Motor pump heater: Voltage | 220 V - 230 V |
Water softener: Regeneration dosage | 300 cm 3 |
Heating element: Resistance | 24,5 Ω |
Motor pump heater: Frequency | 50 Hz |
Single electric water inlet valve: Frequency | 50/60 Hz |
Dimensions + Weight: Wooden door (Thickness) | 16 mm - 20 mm |
Heating element: Heating speed | ~ 2,0 °C/min |
Rotations: Spray arm lower | 30 UPM - 40 UPM |
Data Energy Label: Cleaning Performance | A |
Regeneration: Water hardness | 0 - 60 (53) °dh 0 - 10,7 mmol/l 0 - 107 °fh |
Electronic boards: Serial boards (DLB) | 4619 724 73362 |
Flow rates/ Inlet volume: Drain pump | 16 l/min |
Размеры + Вес: Размеры продукта (Высота) | 82,0 cm - 87,0 cm |
Regeneration: Number of cycles with 2 kg salt | ~ 26 |