Схема узла
Запчасти для посудомоечной машины Whirlpool ADG 8640 WH n.prod.
Характеристики:
Water pressure: Inlet pressure | 0.3 bar - 10 bar |
Rotations: Drain pump motor | 3000 RPM |
Detergent capacity: Rinse aid dosage | 135 cm 3 |
Electronic boards: Serial boards (Data set) | 720021 |
Dimensions + Weight: Wooden door for Integrable types (Weight) | max. 5.5 kg |
Regeneration: Position 0 | after wash cycles 12 Water hardness 0 - 5 °dh 0 - 0.9 mmol/l 0 - 9 °Fh |
Flow rates/ Inlet volume: Shower/Spray arm top | ~ 8 l/min |
Spray pump motor permant spray system: Voltage | 220/ 240 V |
Heating element: Temperature on surface | ~ 115 °C |
Potentiometer: Points of meassurement: (Position 2) | 1.0 k Ω |
Detergent capacity: Prewash | 10 cm 3 |
Drain pump motor: Power Consumption | 30 W |
Coil of dispenser: Resistance | 1.3 k Ω |
Flow rates/ Inlet volume: Spray pump | 45 l/min - 65 l/min |
Regeneration: Position 5 | after wash cycles 2 Water hardness 29 - 35 °dh 5.1 - 6.3 mmol/l 51 - 63 °Fh |
Program information: | All programs will be locked after start. Changing the program or ?nishing the program will be possible only after pressing the start button for longer then 1.5 sec. (Break by customer) A switching off the appliance or unplug the appliance for a while, this will frozen the program step and later on, the program continuos on the same position. Exception: Switching off the appliance or unplug the appliance during the drying phase, this will lead directly to the end of the program. |
Электрические базовые данные: напряжение | 220/ 240 V |
Heating element: Safety thermostat self reset (Temperature of water) | ~ 85 °C |
Rotations: Spray pump motor | 2800 RPM |
Heating element: | 1 Element system |
Electronic boards: Serial boards (Basic UCB, not programmed) | 4619 724 17411 |
Single electric water inlet valve: Resistance | 3.76 k Ω |
Data Energy Label: Drying Performance | B |
Single electric water inlet valve: Voltage | 220/ 240 V |
Heating element: Power Consumption | 1.87/ 2.04 kW |
Regeneration valve: Frequency | 50/ 60 Hz |
Rotations: Spray arm upper | 30 RPM - 40 RPM |
Flow rates/ Inlet volume: Pump height max. | 1.1 m |
Flow rates/ Inlet volume: Spray arm lower | ~ 33 l/min |
Dimensions + Weight: Wooden door for Integrable types (Width) | 592 mm - 595 mm |
Spray pump motor permant spray system: HI | 69 Ω |
Dimensions + Weight: Wooden door for Integrable types (Max. stick out over lower edge of appliance door) | 92 mm |
Water softener: Resin container | 700 cm 3 |
Potentiometer: Points of meassurement: (Position 3) | 1.4 k Ω |
Heating element: Voltage | 220/ 240 V |
Flow rates/ Inlet volume: Inlet valve | 4 l/min |
Accessory: | If you need spare parts apart from the spare part list have a look in the Service Bulletin 4812 718 40084. |
Regeneration: Position 2 | after wash cycles 7 Water hardness 11 - 15 °dh 1.9 - 2.7 mmol/l 19 - 27 °Fh |
Water softener: Salt container | 2 kg |
Potentiometer: Points of meassurement: (Position 0) | 0.0 k Ω |
Options: | Sani rinse program |
Electronic boards: Serial boards (CB programmed) | 720031 |
Dimensions + Weight: Wooden door for Integrable types (Height of plinth) | min. 93 mm |
Regeneration: Volume | 300 cm 3 |
Drain pump motor: Voltage | 220/ 240 V |
Regeneration: Position 4 | after wash cycles 3 Water hardness 22 - 28 °dh 3.8 - 5.0 mmol/l 38 - 50 °Fh |
Detergent capacity: Dosage steps | 1 ml - 6 ml |
Electrical base data: Total power | 2.0 kW - 2.2 kW |
Potentiometer: Points of meassurement: (Position 4) | 1.8 k Ω |
Coil of dispenser: Frequency | 50/ 60 Hz |
Dimensions + Weight: Product dimensions (Weight) | 50 kg |
Dimensions + Weight: Wooden door for Integrable types (Height) | 515 mm - 600 mm |
Flow rates/ Inlet volume: Spray arm upper | ~ 27 l/min |
Volume: Water Volume Level | Regeneration 0.3 l 15 mm Back rinse 3x 1.0 l 60 mm Prewash 4.8 l 120 mm Main wash 4.2 l 118 mm Intermediate rinse 1 4.2 l 118 mm Intermediate rinse 2 4.2 l 118 mm Clear rinse 4.2 l 118 mm Safety/ overflow 8.5 l 141 mm |
Heating element: Fuse | 206 °C |
Regeneration valve: Resistance | 3.13 k Ω |
Electronic boards: Serial boards () | Programing of version and programmed control board, see "Service" and "Data set" on rating plate of inner door: |
Data Energy Label: Energy Performance | A |
Flow rates/ Inlet volume: Flow meter | 208 lmp/l |
Data Energy Label: Reference program | P5g |
Размеры + Вес: Размеры продукта (ширина) | 59.7 cm |
Drain pump motor: Resistance | 146 Ω |
Succession of programs: Programs () | see program diagram |
Potentiometer: Points of meassurement: (Position 5) | 2.3 k Ω |
Dimensions + Weight: Wooden door for Integrable types (Thickness) | 16 mm - 20 mm |
Электрические базовые данные: частота | 50 Hz |
Coil of dispenser: Voltage | 220/ 240 V |
NTC | 20 °C 58.1 kΩ 25 °C 47.1 kΩ 30 °C 38.2 kΩ 40 °C 25.4 kΩ 50 °C 17.2 kΩ 60 °C 11.8 kΩ 70 °C 8.3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ |
Regeneration: Salt consumption for regeneration | 77 g |
Potentiometer: Points of meassurement: (Position 6) | 2.6 k Ω |
Электрическая база данных: Предохранитель | 10 A |
Water pressure: Spray pump pressure | 0.3 bar |
Размеры + Вес: Размеры продукта (Глубина) | 55.5 cm |
Regeneration: Position 1 | after wash cycles 10 Water hardness 6 - 10 °dh 1 - 1.8 mmol/l 10 - 18 °Fh |
Regeneration valve: Voltage | 220/ 240 V |
Potentiometer: Points of meassurement: (Position 1) | 0.5 k Ω |
Detergent capacity: Main wash | 40 cm 3 |
Water softener: Regeneration dosage | 300 cm 3 |
Heating element: Resistance | 24.5 Ω |
Single electric water inlet valve: Frequency | 50/ 60 Hz |
Spray pump motor permant spray system: HA | 48 Ω |
Spray pump motor permant spray system: Power Consumption | 140 W |
Heating element: Heating speed | ~ 2.0 °C/min |
Rotations: Spray arm lower | 30 RPM - 40 RPM |
Electronic boards: Serial boards (DUB) | 4619 724 06741 |
Regeneration: Position 6 | after wash cycles 1 Water hardness 36 - 60 (53) °dh 6.4 - 10.7 mmol/l 64 - 107 °Fh |
Data Energy Label: Cleaning Performance | A |
Potentiometer: Points of meassurement: () | 1(black) to 2 (middle) |
Spray pump motor permant spray system: Capacitor | 4 µ F |
Flow rates/ Inlet volume: Drain pump | 16 l/min |
Regeneration: Position 3 | after wash cycles 5 Water hardness 16 - 21 °dh 2.8 - 3.7 mmol/l 28 - 37 °Fh |
Размеры + Вес: Размеры продукта (Высота) | 82.0 - 87.0cm |
Regeneration: Number of cycles with 2 kg salt | 26 |